Dull blades tear grass instead of cutting it
When a mower blade loses its edge, the lawn does not just look worse. Frayed grass tips turn brown, clippings clump, and mulching stops chipping cleanly. A sharp replacement pair restores a clean cut without buying a new mower.
- ▪ Brown, frayed tips.
- ▪ A dull blade rips grass fibers rather than slicing them, leaving straw-colored ends that turn brown within a day or two.
- ▪ Clumped, uneven cut.
- ▪ Worn edges push and drag clippings into piles instead of dispersing them, leaving streaks and missed patches.
- ▪ Poor mulching.
- ▪ Blunt lifting fins fail to circulate clippings, so grass drops in long strands instead of chipping into fine mulch.
- ▪ Extra engine strain.
- ▪ A dragging blade forces the mower to work harder, shortening run time on a battery mower and raising fuel use on gas.
A sharp pair that chips grass and cuts clean
These two hardened-steel mulching blades are made to chip clippings into fine pieces, support even side discharge, and bring back a crisp, uniform finish on a standard 20-inch deck.
Angled cutting edges and lifting fins chip clippings into small pieces that break down quickly on the lawn.
The matched pair sits balanced across a 20-inch deck for a consistent sweep without missed strips.
Tempered steel holds an edge longer and resists bending from twigs and debris.
Fits with basic hand tools once you match the center-hole pattern to your mower.
Built to hold an edge season after season
Each blade is made from tempered steel with a ground sharpened edge and a formed lifting fin, then delivered as a matched pair for balanced rotation.
- ▪ Tempered hardened steel.
- ▪ Resists flexing and impact when you hit gravel, twigs, or uneven ground.
- ▪ Ground cutting edge.
- ▪ A beveled slice edge cuts cleanly on the first pass instead of shredding.
- ▪ Formed lifting fin.
- ▪ Curved fin lifts clippings upward for recirculation and fine mulching.
- ▪ Matched pair.
- ▪ Both blades share length, pitch, and balance so the deck spins smoothly.
Swap in four simple steps
No shop visit required. Change the blades in your garage with basic tools after confirming fit.
Measure deck width to 20 inches and compare the center-hole and bolt pattern before ordering.
Disconnect the battery or spark plug and tilt the mower with the air filter up.
Hold the blade steady, loosen the mounting bolt, and take out the worn pair, noting washer order.
Fit the new pair in the same orientation, torque the bolt to your mower manual, and spin-check for balance.
What you get, in plain numbers
Standard dimensions for a 20-inch walk-behind deck; always cross-check your mower manual before fitting.
| Specification | Value |
|---|---|
| Product | 2-Pack 20-Inch Replacement Mulching Mower Blades |
| Material | Tempered hardened steel, ground cutting edge |
| Color | Silver metallic |
| Deck fit | Standard 20-inch walk-behind push / self-propelled deck (verify center-hole pattern) |
| Blade length | Approx. 20 in (508 mm) per blade |
| Includes | 2 mulching blades; mounting hardware not included |
| Warranty | 30-day replacement on defects |
Note: Center-hole and bolt patterns vary by mower brand and model. Compare your old blade hole shape and washer stack with the product photos before ordering; this is a generic compatible replacement, not an original-equipment part.
Three ways to handle a dull cut
Same brown lawn, three choices. Here is how they line up.
| At a glance | This product | Alternative |
|---|---|---|
| Cost | Low: two replacement blades | High: a whole new mower |
| Lasts | A full cutting season per pair | Depends on a professional service |
| Fit | Check center-hole pattern at home | Book a shop visit |
No surprises in the pack
You receive the blade pair only; the mower itself and mounting bolts are not included.
| Specification | Value |
|---|---|
| Product | 2-Pack Mulching Blade Set |
| Includes | 2 hardened-steel mulching blades |
| Material | Tempered steel |
| Color | Silver |
| Weight | Approx. 2.6 lb per pair |
| Fit | 20-inch standard deck; verify hole pattern |
| Warranty | 30-day defect replacement |
Two matched 20-inch mulching blades ready to install after a fit check.
Mower, battery, and mounting hardware are not included; confirm the center-hole pattern against your old blade.
Keep the edge between swaps
A few habits stretch the life of a fresh pair and protect your mower.
- ▪ Raise the deck on rough ground.
- ▪ Slow down and lift the blade over gravel, roots, and hard edges to avoid nicks.
- ▪ Clean after each cut.
- ▪ Rinse grass buildup from the deck and blade so moisture does not start rust.
- ▪ Sharpen seasonally.
- ▪ Touch up the edge twice a season and keep both blades matched for balance.
- ▪ Store indoors.
- ▪ Keep spare blades dry and off concrete to prevent surface rust.
They suit most standard 20-inch walk-behind decks, but center-hole and bolt patterns differ. Compare your old blade hole shape and washer stack to the photos before ordering.
No. These are generic compatible replacement mulching blades, not branded OEM parts; the mower itself is not included.
Mounting hardware is not included; reuse your existing bolts and washers, or replace them if worn.
Plan on a fresh pair each cutting season, or sooner if you nick the edge on gravel or notice a brown, torn cut.
Yes, a dull edge can be sharpened, but once a blade is bent, pitted, or thinned, replacement gives a safer, more balanced cut.
- ▪ Two hardened-steel 20-inch mulching blades for a clean, chipped cut.
- ▪ Fits most standard 20-inch decks after a center-hole check.
- ▪ Easy home swap with basic hand tools; no shop visit.
- ▪ Mower and mounting hardware not included.
A sharp matched pair brings back a clean, even lawn without buying a new mower. Check the hole pattern and order your pair.
Reviews
There are no reviews yet.